Maslinovo ulje servo motor pokretano četverosjemske klipove punjenje ROPP metalnim čepovima s dvostrukim stranama strojevi za etiketiranje kvadratne boce linija za punjenje potpuno automatski

Opis

The line specially designed for our russian customer who sent to us the glass bottles (thin&tall) is suitable for food packing industry like olive oil/wine bottles fill-cap-label process.

Samples offered by our EU customer

The whole line including filling capping labeling machine

1.model NPACK-5030 piston filling machine
2.model NPACK-AC40 ROPP capping machine
3.model NPACK-650A double sided labeling machine
4.Nitrogen gas flushing function after filling
5.Accumulation turntable for collecting final product

As below there is the basic description &introduction one by one :

►Model NPACK-5030 four heads piston filling machine

The 4heads olive filling machine,controlled by the microcomputer,combines the photoelectricity with pneumatic operation,

thus widely is applied for the liquid filling of the agriculture chemical、solution、liquid detergent、cosmetic as well as olive.The filling volume is precise,foamless and stable.

The machine can fill the liquid with the range from 25-1000ml,meanwhile there is no special requirement on the shapes of bottles.That is to say,it can fill the liquid for the normal bottles as well as the irregular-shaped bottles.

Model       NPACK-5030

Filling range     50～3000ml

Filling speed　       ＜20-30b/m（for 500-1000ml liquid）

Točnost ± 1%

Snaga / snaga napajanja 0,8kw 、 220v

Radni tlak 5 ～ 6kg / cm3

Air consumption　  0.5-0.7mpa

SW 500kg

Outer dimension      2000×800×1900mm

Mark:The filling nozzles can be designed and manufactured according to requirements from customers on the filling range and filling speed

Filling speed adjustment

Filling speed adjustment has the following 6 factors:

1, the speed of the product is determined by the viscosity of the product and the length of the suction pipe.

2, filling speed depends on the diameter of the filling head, the diameter is large, the speed is quick.

3, the product of the bubble level. The product filling speed of the high bubble should be slowed down.

4, how much is the filling quantity.

5, the accuracy of the filling quantity, adjust the filling time of each cast.

6, adjust the filling speed (that is, the speed of the servo motor).

General trouble shooting and processing

1）Touch screen is not shown, but the indicator light

Fault cause:

Check whether the fuse is burning, or the contact is bad, replace or reinstall the fuse.

2）The output indicator of the programmable controller has an output indicator, but the solenoid valve does not work.

Fault cause:

Upon examination of the solenoid valve failure, is the key to the programmable controller in the electrical damage, can replace the same type of intermediate relay, fault can be ruled out (this fault is very rare).
3）The main head there is a leak in the shutdown.

Fault cause:

The filling head cylinder does not move up and down, replaced PTFE head, check on the stingy joints have gas, or replace the filling valve, can be ruled out

4）After filling in a number of bottles do not fill

Fault cause:

♦Check whether the bottle counting electric eye, if not counting adjustable electric distance, so that it can reach the count;

♦ Check that the liquid level indicator is black, if it is white, and the liquid level is fluid, and can be filled with black

♦ Check the magnetic switch cylinder after the dive, the light is bright, if not bright, adjust to the light.

♦Check the back of the servo motor is close to the switch is bright, if not bright, adjust to the light.

5)Individual valve or cylinder action to slow down or do not work.

Fault cause:

♦The general situation is caused by the fault of the control valve, first check to control the output of the output of the display lamp (in the lower left of the programmable controller) work is normal, confirm the normal operation of the following check.

♦Magnet coil plug for transposition of the solenoid valve, if change the position of the fault, indicating that the electromagnet coil is damaged, replace the coil after failure can be ruled out.

If the valve group of the emptying port does not stop to have a lot of gas, the system has a more serious leakage. Can check the internal sealing condition, if damaged, should be replaced. If the fault can not be ruled out, can check the valve spool movement, see if there is a card phenomenon or the seal is damaged, and repair, if damaged more serious, it should be replaced by the entire valve.

6）Servo motor alarm.

Fault cause:

♦Check whether the PLC on the F**, if it is to turn off the power, and then open up to manual operation, a number of seconds after the manual injection, and then press the manual back to zero.

►Nitrogen gas flushing system

NPACK-AC40 Automatic ROPP capping machine for olive bottle with metal caps with protective chamber

automatski ROPP aparat za zatvaranje s upravljačkim sustavom tipki

Prekrivačke glave za ROPP poklopac

Stroj za zatvaranje je prikladna oprema za zatvaranje aluminijskih poklopaca za plastičnu bocu, bocu za kućne ljubimce, kao i staklenu bocu. Predodređuje zatvaranje boce ispod prevrtanja s ploče za kuhanje, automatski punjenje boce 、 Poklopci, uklanjanje obrnutih čepova. Boca s poklopcem pogoduje karakteristikama poput stabilnog efekta zatvaranja, pogodnog zatvaranja, tako da djeluje kao krivotvoreni i protiv krađe

Model NPACK-AC40

Dovodni prah (V / Hz) AC 220/50 380/60

Kapacitet (m / min) ≧ 4000B / M

Veličina kapice (mm) 250-1000

Primjena Alum-kape

Ispuh zraka iz vakuumske pumpe (m3 / h) 5KG

Vanjska dimenzija （L × Š × V mm (mm) 2000 × 1000 × 2300

NG (kg): 520

Crtanje ROPP procesa ograničavanja (uzimanje primjera kao automatska linija s transportnom platformom)

How to operate model NPACK-C25 Single head ROPP capping machine

Spremnik za dovod, koji se kreće po transportnoj traci, ubacuje se u zvjezdani kotač kroz dovodni crv, zvjezdani kotač koji dovodi spremnik ispod glave za brtvljenje u narednom dijelu indeksiranja, što znači dok poklopac boce uzima poklopac s otvora za punjenje čepa za punjenje zdjelu, gdje su tijelo i vrat spremnika postavljeni ispod rotirajuće glave, gdje brtvena glava savršeno radi operaciju navoja i brtvljenja.

Istaknute značajke :

Jedinica je izrađena kompaktna i svestrana.
SS Slat transportna traka
SS elegantno mat završeno tijelo
Ugrađena je na prednjoj upravljačkoj ploči
Vibracijska zdjela
Uz frekventni pogon A / c

►model NPACK-650A double sided labeling machine

The labeling equipment is for the round bottle labeling in the industry like food、oil、pharma、wine、cosmetics and so on.

The machine with elegant design can be easily operated and maintained by the common worker,

who requires no special training in operation this machine.Just give a simple adjustment to produce another product when you want to swap the different kinds bottle labeling.

Metal caps capping+labeling line

The bottle labeler is thus out from as below-mentioned characteristics:

1: Glavni dio opreme čine SUS304 i napredni aluminijski proizvodi.

2:The labeling heads is driven by the stepping motor that is imported from Japan.

3: Sva oprema za senzore svjetla uvozi se iz Japana i Njemačke

4: PLC Nadzira se sučelje čovjek-stroj sa 60 memorijskih jedinica

5: Stroj je najbolji izbor za rad jednog radnika.

6: Stroj ima funkciju uspravljanja boca, raspodjele boca, označavanje 、 flaktiranja i brojanja.

7: Kut oznake položaja „visina“ može se lako podesiti.

8: Opremljen transportnom trakom, stroj se postavlja na set proizvodne linije.

Basic parameter of double sides labeling machine

turntable for accumulation of final product